Burlington Safety Laboratory, Inc. - Substation Cover-Up
Burlington Safety Laboratory, Inc.
Bookmark     Home       About Burlington Safety       Online Catalog       Catalog Index      Resources      Contact Us
Services:
  > Laboratory Testing
  > On-Site Testing
  > Calibration & Repairs

Quick Shop:
(Kits shipped within 24 hours)
  > Safety Kits

Products:
  > Line Hose & Covers
  > Blankets
  > Plastic Guards and Covers
  > Outage Protection
  > Gloves & Sleeves
  > Dielectric Footwear
  > Insulated Jumpers
  > Grounding Equipment
  > Hot Sticks & Tools
  > Insulators
  > Eye & Head Protection
  > Arc Flash Clothing & Kits
  > Accessories
  > Industrial Safety Equipment
  > All Products
 Search Catalog
      GO   
 All Categories    Substation Cover-Up
View CartView RFQ'sExpress Ordering
 Shopping Cart  0 items 
 Request for Quote  0 items 
All Categories > Plastic Guards & Covers > Substation Cover-Up > View Items 

Substation Cover-Up
Check up to five results to perform an action.

Item Image - Substation Cover-Up 1376

larger image 		Substation Cover-up and barrier equipment is used during routine maintenance where accidental contact may occur. This barrier equipment is often used where outages are difficult to reach and the occurance of accidental contact is high. These covers may be applied with rubber gloves or hot sticks. These covers are made from Type I orange ABS plastic. This equipment is not intended for permanent or semi-permanent barrier or insulating applications. Use these covers to protect against accidental contact only. These covers are not to be left installed for extended periods of time especially when in contact with both a grounded and energized object.

Bus Guards are easily interlocked with each other. To interlock units determine the length of bus to be covered. Place one unit on the bus then the other, pulling it over the first cover until the dimples interlock at the required length. This guard has a voltage rating of 36.6 kV (guarded Ø to guarded Ø).

Bus “T” Guards interlock two or three bus guards at bus tap “T” connections and 90 degree angles. To interlock units, first position the bus guard then slide the “T” guard over the top interlocking the dimples. This guard has a voltage rating of 36.6 kV (guarded Ø to guarded Ø).

Bus End Guards cover the ends of a substation bus supported by station post insulators. The slot and insulator grip hole can be easily enlarged in the field with a sharp knife. This cover also has a guide bead for a trim fit. This guard has a voltage rating of 26.4 kV (guarded Ø to guarded Ø).




    Print Printable Page  
    Email Email This Page  
    Save To Favorites Save To Favorites
  
Request InformationCompare Items   Results per Page : 
  Results 1 - 9 of 9 1 

Item #

Item Name

Std. Pkg. Qty.

Pkg. Wt.

1374 Guard, Substation Bus 1 6 lbs.
1375 Guard, Substation “T” Bus 1 4 lbs.
1376 Substation Switch Barrier 43 x 52 1 12 lbs.
2413 Guard, Switch Jaw, 13" x 24" 1 7 lbs.
2418 Guard, Switch Jaw, 8" x 18" 1 4 lbs.
2424 Guard, Switch Jaw, 8" x 24" 1 5 lbs.
9992 Guard, Substation Bus End 1 5 lbs.
24219 Cover, Switch Jaw 1 4 lbs.
24455 Guard, Switch Jaw, 8"x16" 1 2.25 lbs.
  Results 1 - 9 of 9 1 
Contact Us Today ...

Toll-Free: 1.800.220.2120
info@BurlingtonSafety.com
Nail for Pet We Represent: While Safety Line

Copyright © 2008 Burlington Safety Laboratory, Inc. • All Rights Reserved
Website by B2B Design & Development LLC

Browse CatalogRFQ